• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Bob Easton

Chocolate powered woodworking

  • Home
  • Grinling Gibbons Tour

Two Mallets Followed Me Home

November 20, 2009 by Bob Easton 5 Comments

picture of logWe live within a hundred yards of a woodlands, a large state park. My better half and I went hiking there a couple of days ago. On the way back home, I spotted a small log hiding under a guard rail along the roadside. A maintenance crew goes along the park roads every fall trimming limbs and trees that might fall upon the roadway during ice storms. They usually saw logs into firewood length and leave them to be picked up by whoever wants them. Someone missed this little log of black locust. I could see a couple of mallets inside that log, so I picked it up and carried it home (which worked off at least a Snickers bar).

piecs of lumberI wanted to reduce this log a bit to help it dry without splitting too much. I would really like to rive the wood rather than cut it, but there are not yet any tools for green woodworking in my shop. My solution was to use a coarse setting of my #40 scrub plane to make flats on either side of the log. Then, a few passes through the band saw reduced it to pieces I think will be useful for mallet heads and handles. Those are set aside to dry for awhile.

I’m not certain on the design yet.  Maybe a sawed head, maybe a turned head. Of course, for the turned head I don’t have a lathe that’s large enough. I’ve been wanting to build one of “St. Roy’s” spring pole lathes. To be continued…

Filed Under: Hand tools, Shopmade

Shopmade Scratch Awl

November 20, 2009 by Bob Easton Leave a Comment

picture of scratch awlA scraggly old broken spring hook (tool “G” at this link), with the broken off end roughly resharpened to a point, served as a scratching tool for many years. Now, with the ability to neatly grind metal, and a little scrap of oak, it takes new form, a finished scratch awl. There’s really not much to it. I turned the handle in a small model making lathe. The awl itself is that old tool reground and polished.  3M microabrasive film is fantastic for polishing. The ferrule was donated by a self-sacrificing Pentel mechanical pencil. Finish is several coats of danish oil.

Yes, it is small. It fits the palm easily. As shown in this picture, I was using it to prick through a paper pattern to prepare for cutting a boat part.

Filed Under: Hand tools, Shopmade

Shopmade Router Plane

November 17, 2009 by Bob Easton 5 Comments

Someday…  Someday, I’m going to need a router plane. Router planes are used to clear the waste from a dado groove. I really don’t need the plane today, but have some projects in mind for the future that will need dado joints.

picture of router planepicture of blade and blade holderI based this plane (also called an “old woman’s tooth”) on an example made by Derek Cohen. A bit of 5/4 ash left over from the Fiddlehead boat was the starting point. Shaping was much as Derek described; drill a few holes, cut the outline with the shopmade turning saw, refine with rasps. Now that I can shape metal, the tooth / blade was shaped from a hex key. Hand cranking the grinder to shape the blade burned off a hand full of mini Tootsie Rolls. A screw insert and a thumb screw were the last of the parts. A couple of coats of boiled linseed oil, followed by a coat of danish oil finished the job.

picture shows depth settingYes, it cuts as intended. This hex key yielded a 1/4 inch wide blade, which will be handy for the intended projects. The method used to set the depth of cut is to elevate the tool on a couple of old business cards and then drop the blade to the wood surface and tighten the thumb screw. Now, remove the cards and cut. Repeat til done. By the way, it is a real good thing to cut from the outsides of a groove toward the center. That avoids tearout at the edges.

For those who have no old business cards for depth setting, use two aces out of a deck of playing cards. Leave them in the shop, so the next time you have friends over for poker, you know where at least two of the aces are.

Filed Under: Hand tools, Shopmade

  • « Go to Previous Page
  • Page 1
  • Interim pages omitted …
  • Page 84
  • Page 85
  • Page 86
  • Page 87
  • Page 88
  • Interim pages omitted …
  • Page 129
  • Go to Next Page »

Primary Sidebar

Footer

Recent Posts

  • Sign Your Work!
  • New Frame Saw / Scroll Saw
  • Lamppost Sign
  • Goodbye PayPal – Goodbye Bob’s eBooks
  • Anarchist’s Workbench is Done

Categories

  • About
  • Artwork
  • Boatbuilding
  • Boating
  • bowl carving
  • Boxmaking
  • Clocks
  • Drawings
  • eBook
  • etude
  • Eva Too
  • Eva Won
  • Fiddlehead
  • Fiddlehead model
  • Flying
  • frame saw
  • gilding
  • green woodworking
  • Grinling Gibbons
  • Guns
  • Hand tools
  • Humor
  • kerfing plane
  • Lettercarving
  • Mill Creek 13
  • Model building
  • Power tools
  • Rant
  • resawing
  • scroll saw
  • Shopmade
  • sign painting
  • Stonework
  • Swimming
  • Technology
  • The Wall
  • treadle lathe
  • Uncategorized
  • VSD
  • Woodcarving
  • Woodturning
  • Woodworking
  • workbench

Other stuff

  • About
  • Contact
  • Privacy Policy

Copyright ©2024 · Bob Easton · All Rights Reserved