• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Bob Easton

Chocolate powered woodworking

  • Home
  • Grinling Gibbons Tour

Resawing Boat Lumber

December 15, 2008 by Bob Easton Leave a Comment

harry-strasil-avatar
Harry’s self portrait

My question about resawing very long lumber was answered some time ago on the Sawmill Creek Forums with a very fine suggestion by Harry Strasil. He offered good suggestions about using a saw table and stool for holding the work, and described very precisely how to build a frame saw tuned for the job . One of his other entries has a couple of pictures of using such saws and benches.

As shown in my previous entry, I built a frame saw somewhat similar to what Harry described. I varied from his suggestion by using a purchased blade instead of cutting down an old rip saw.  As an aside, I recently acquired an old Disston D-8 rip saw from fleabay. The blade had undergone enough pitting that the engraving has almost completely disappeared, so I can’t date it from the engraving. At some point there was a chemical restoration that stopped the rusting and left the blade in pretty good shape. The saw nut with the Disston medallion dates between 1896 and 1917. That saw cuts so well that I decided to keep it for ripping rather than cut it down as Harry suggested.

center marking tool center marking gauge

Along the way, I took a short diversion to make a marking gauge. The usual marking gauge is used to mark a prescribed distance from an edge. For this work, the task is to mark the center line along the board’s edges. The tool doesn’t need to be very refined. Rough sawn cedar flitches are far from smooth, so anything that will rumble along those rough surfaces is fine. It’s a simple self-centering gauge made of two pieces of birch dowel, a scrap of oak, and a bit of six penny nail. It would work okay as a simple rectangular slug, but I like a little more shape, and this shape actually makes it easy to cant the gauge to hug the lumber. The shape is inspired by DaVinci.

Hint for anyone making one of these: If you use an aggressive auger (in a brace) to bore the holes for the pins, it is a very good thing to bore those holes in the oak stock before cutting it to length or making any decorative shapes. Don’t ask how I know.

resaw bench

The bigger puzzle was how to hold the workpiece. I have a pair of great saw benches that are exactly the right height. One of them now has a simple modification, two vertical rails added between an end stretcher and the top of the bench. They are mortised into the bottom of the bench top and screw attached to the stretcher. The space between them is about 1 and 1/2 inches. The space from stretcher to bench top is 10 and 1/2 inches. Most any board I want to resaw can be stood on edge within that space. Then, wedges are used to center the board vertically and to push it up against the bench top. The fit snugs up nicely enough to not need any other clamps.  This ended up being a very simple solution which seems to work well. I haven’t yet discovered the saw blade’s optimum attack angle, but will soon. The ergonomics feel right with the saw just wide enough to be evenly guided by knobby knee bones.

resaw with bob

The test piece shown in the first pictures is about four feet long. When I get to resawing a sixteen foot piece, I was expecting that I would need another pair of vertical rails installed on the second saw bench. Not needed. A quick set up finds that a simple pair of wedges on that other bench will be enough. Time to find some good music and get to sawing.
resaw 16 footer

Filed Under: Boatbuilding, Hand tools, Woodworking

New Frame Saw

December 13, 2008 by Bob Easton

A few new cedar flitches are acclimating themselves to the shop. In the meantime, I’ve been busy preparing a saw that will be used to get planking out of that cedar. This saw’s main work will be resawing, slicing thickness from roughly 4 quarters to pairs of roughly 2 quarters boards. Getting two boards from each flitch is the goal. Most people would use the bandsaw for this job, but mine is good for only 6 inches of resaw capacity, and some of these boards will be from 8 to 10 and 1/2 inches wide. I would rather have a good hand tool method than invest yet more in the band saw.
frame saw

This frame saw derives from Josh Clark’s “Making a Frame Saw” article. I used red oak, 1 and 1/2 inch square, for the stretchers. The arms were gotten from a piece of the same oak, resawn to half thickness. The blade is also 1 and 1/2 inches wide. I found it at Frog Tool Company in Dixon Illinois. See the update at the end of the article.

frame saw

As Josh suggested, I used half-blind dovetail joints. While I’m skeptical that the forces on the saw actually need this kind of joint, I saw it as opportunity to learn to do them. First time doing dovetails. I cut the tails on the arms first and did a couple of practice pockets on scrap wood. Then, did the real ones. Each one gets better, and yes, that’s the last one that’s shown in the picture. All are snug enough to require gentle tapping to assemble. No glue used so far. (Note from several years later: These joints are still not glued or screwed. The tension from the saw keeps them firm enough for constant use.)

saw fastening

All edges are chamfered, because I imagine I’ll spend quite a few hours using this saw. I’m an Art Deco fan, so the upper arm has a series of stop chamfers in an Art Deco motif, and a wing nut to match. The wing nut is simply a wooden shell covering a 3/4 inch metal nut.

The first cut, on a 7 inch wide board, shows the saw will indeed do the job well. Planing will be needed to smooth the cut surfaces, but that was expected. Now, all I need to do is figure out how to hold a workpiece that’s 16 feet long.

IMPORTANT NOTE: After using this saw for a couple of months, I came to dislike the blade. I acquired a good old Disston 26 inch saw, changed it from 7 TPI to 4 TPI, sharpened, and hacksawed to a 2 inch width. That replaced the original blade an made a huge improvement in how well the saw works.

Filed Under: Boatbuilding, frame saw, Hand tools, resawing, Shopmade

New Bow Saw

December 6, 2008 by Bob Easton 5 Comments

A few weeks ago, I cursed a wretched coping saw as I cut the oval hatches in the Fiddlehead’s bulkheads. A week or so later, I needed a turning saw to cut the long gradual curves on the Fiddlehead’s bottom, and actually hacked together a temporary saw from a hacksaw frame and part of a used bandsaw blade. It worked, but it’s a good thing the curved line wasn’t too far from the edge of the board.

Those incidents led me to make a bow saw. Of the available designs, I found the Gramercy Tools design most appealing. The design is classic, yet uses a moderm pair of brass pins to hold the blade. The pins can accommodate blades that already have pins pressed in, or blades that have open eyelets. The Gramercy bow saw is available from Tools for Working Wood as a completed saw for $139.95, or as individual parts. Gramercy offers a very complete set of drawings for people who want to make their own. I chose to buy only the pins and blades and make all the wooden parts myself. While they use Hickory, I used Oak because that’s what I had on hand.

Features that appealed to me are: the classic style, the curved faces of the mortise joints on the stretcher (fun cutting them, allows for slightly varying blade lengths), and the subtle sculpting of the various curves and edges, including a finger rest near the base of the cheeks.

The pins are glued into the handles with epoxy. I used a couple of coats of boiled linseed oil for finish. It still needs a good cord for tensioning. The fuzzy hemp is temporary, enough to try it out. The blade is 12 inches long. This blade is the coarsest of a set of three, 10 tpi.

That little squiggly block of wood represents the first cut, an S shape about an inch long, through 4/4 cedar. The saw ends up being very light and pleasing to use. While I thought the handle a bit small when I was turning it, I find that it falls very naturally into the hand. Gramercy did a fine job on the design. This one is a keeper!

For Luke and Dan: Yes, I used electrons while building this saw. I used a bandsaw to resaw the oak to useful dimensions, and I used an ancient miniature lathe to turn the handle, toe, and toggle. The lathe was only moderately easier than hacking them out with a pocket knife. Oh yes, there are also electric lights in the shop. The remainder of the making used hand tools, rasps and the eggbeater drill.

So now, we’ll have many fewer colorful words while sawing.

Update (12/13): Those brass pins from Gramercy are so smooth that the saw frame wants to rotate around them a little too easily. More tension? The blade already sings a high C when plinked. A small sliver of 320 grit sandpaper inserted along with the pin provides exactly the right friction. For long time coping saw users, this saw is a great upgrade. Break the habit of taking short stokes, Use the entire length of the blade and be amazed at how easily the saw works.

Filed Under: Hand tools, Shopmade

  • « Go to Previous Page
  • Page 1
  • Interim pages omitted …
  • Page 99
  • Page 100
  • Page 101
  • Page 102
  • Page 103
  • Interim pages omitted …
  • Page 129
  • Go to Next Page »

Primary Sidebar

Footer

Recent Posts

  • Sign Your Work!
  • New Frame Saw / Scroll Saw
  • Lamppost Sign
  • Goodbye PayPal – Goodbye Bob’s eBooks
  • Anarchist’s Workbench is Done

Categories

  • About
  • Artwork
  • Boatbuilding
  • Boating
  • bowl carving
  • Boxmaking
  • Clocks
  • Drawings
  • eBook
  • etude
  • Eva Too
  • Eva Won
  • Fiddlehead
  • Fiddlehead model
  • Flying
  • frame saw
  • gilding
  • green woodworking
  • Grinling Gibbons
  • Guns
  • Hand tools
  • Humor
  • kerfing plane
  • Lettercarving
  • Mill Creek 13
  • Model building
  • Power tools
  • Rant
  • resawing
  • scroll saw
  • Shopmade
  • sign painting
  • Stonework
  • Swimming
  • Technology
  • The Wall
  • treadle lathe
  • Uncategorized
  • VSD
  • Woodcarving
  • Woodturning
  • Woodworking
  • workbench

Other stuff

  • About
  • Contact
  • Privacy Policy

Copyright ©2024 · Bob Easton · All Rights Reserved