Bob Easton

The eBay seller warned that hand saws were not part of her expertise. So, I didn’t ask for details. The photos were good enough to think it worth bidding.

Richardson, later Richardson Brothers, was a saw manufacturer in Newark New Jersey, about 20 miles down the road from where we live. From what I’ve learned, Richardson made highly respected products. They had one of the early patents for taper grinds on full length saws. Long story short, it seems they were also a very strong competitor to Disston. One contention is that around 1890 Disston manged to “do away” with some of its competitors by buying them and throwing them into a conglomerate known as “National Saw” which died in 1906.

This particular saw has a medallion that carries the 1867 patent indication placing it later than that date, and before the company started marking their products with a “Richardson Brothers” brand in the late 1870s. The stamping on the spine is an arched “Richardson” with “Newark NJ” below the arch, “Cast Steel” to the left, and “Warranted” to the right. The blade measures 14 inches long and has a depth under the back of  3 and 3/8 inches. It is 0.029″ thick.

This saw did not lead as sheltered a life as the Disston #4 I restored a couple of weeks ago. Whoever owned this Richardson used it hard,  probably never sharpened it, and then left it where it gathered a good bit of rust and pitting and lost most of the finish on the handle. The area of the handle where one grips still had a little varnish and several kinds of “donor paint.” The end where it meets the plate was bare, dry, and heavily stained. The upper horn has a bit split off the underside and presents a ragged edge to the web of the hand that holds it. The plate has no dents and is absolutely straight, as is the spine. It was filed 12 TPI, rip, and arrived in my hands with absolutely no set.

I restored this blade the same way I did the Disston, with a (very long) bath in Evapo-Rust and then lots and lots of sanding. There is still a good bit of pitting and maybe a long session with a belt sander could solve that, but my belt sander has yet to be purchased. I sanded off what little finish remained on the handle and sanded some of the stains away. There’s no need to reshape this handle because it was already of the era when they made them nice and comfortable. As for the split out area on the upper horn, I voted against splicing in a repair and simply carved that area to a new smooth profile. I’m unsure, but think the handle material to be apple which was very prevalent at the time. Finish is 3 coats of clear shellac ending with wax rubbed in with steel wool.

My sharpening required reducing the teeth down to about 50% of their original height before I got a nice row of flat spots to work from. Then I sharpened the toe end with relaxed rake for a couple of inches with the rest sharpened at near zero rake, all on the original 12 TPI. I now have two very nice back saws and might opt for a third for smaller dovetail work.

 

It’s time to do something about a woefully inadequate saw collection. Other than my shopmade frame saw and shopmade turning saw, my other saws are modern disposables that probably wouldn’t be good enough for a rough carpentry contractor.

Mass production of western style handsaws started a nose dive in the middle of the last century and have brought us to cheap, colorful, plastic handled blister raisers with brittle teeth that can’t be sharpened. Yes, there are a few premium western saw makers currently making superb saws. If those are your fancy, a good Google search will find many of them for you. For myself, I like refurbishing older tools. So, it was off to eBay to find my first goal, a small back saw suitable for fine joinery.

This Disston Nbr. 4 is has a 10 inch blade, has a plate depth of 2.5 inches under the back, plate thickness of 0.031″, is filed for 12 teeth per inch rip, and has a steel back. The blocky, semi-ugly beech handle dates it to after 1940. There’s no stamping on the back (also after 1940), and the etch on the plate dates it to the post WW II era.  Disston was sold in 1956, placing that as the most recent date possible for this saw. This saw had a very easy life. It was barely used and apparently kept in a comfortable place. The handle seems to have original factory finish, with no chips or other damage, not even significant scratches, but some runs. There’s a little bit of donor paint and other stains. The blade has minor rust, a bit of pitting, and “patina.” The teeth are still relatively sharp. The tooth line has an ever so slight bow. The spine has no visible bowing. Before I did anything with it, I tried a few test cuts and found it maybe 20% slower than the spectacular yellow and black Stanley utility saw.

Since it is neither rare nor collectable, and screams won’t be heard if I don’t leave it “pristine,” I intend to refurbish it in the manner pursued by Andy “Brit.” That means a very shiny plate. After disassembling, the first stop was in an Evapo-Rust bath. This is the very first “eco friendly” clean-up product that actually has the strength to do what it advertises. Mild rust was gone quickly. Then it’s off to the polishing. I used garnet paper starting at about 250 grit, then wet-n-dry to 600, followed by Abralon sanding pads to 4000. The purists will be upset with losing part of the etch, but it’s a “user” not a collector’s item. That slight bow was removed by clamping the saw in my really simple “saw vise” just above the tooth line and then tapping along the spine with moderate hammer blows buffered by an oak block.

The handle is actually beyond semi-ugly. It is downright ugly and uncomfortable too. It wants some serious reshaping. Any self-respecting saw handle would like to look the part, and I wanted to soften some hard lines, and have a finish that did not includes the runs and curtains of the original poor manufacture. Search around and you’ll see that classic handles had a nib on the top, a lamb’s tongue on the bottom, and curves that actually flowed nicely. Out came my marker, turning saw, a few gouges and a couple of rasps. Reshaping it was so much fun that I lost track of time, maybe and hour or two. Finish is three coats of shellac followed by paste wax applied with steel wool. Satin s-m-o-o-o-o-o-o-t-h! The brass finished up relatively quickly with the Abralon pads followed by rottenstone in wax and buffing.

Lastly, comes sharpening. I’m constantly amazed at how many people think saw sharpening some mysterious art. I see it as a fundamental skill for anyone working with hand tools. Why send something out to be sharpened? Why bear the expense and delay. (Some of those premium saw makers offer sharpening services, but have backlogs measured in weeks and months.) Learning to sharpen a saw is something that can be accomplished in only a couple of hours and is a lifetime skill that improves whenever you use it. Once you know how, you can sharpen a saw in less time than it takes to stand in line at the post office. Learn here, or if you’re a member of Paul Seller’s Woodworking Masterclasses online school, learn here. Also, be aware that rip filings do cross cutting surprisingly well, so you can do a lot with the simplest filing technique. I used Seller’s advice and filed the first dozen teeth at the toe of this saw with 10-12 degrees of rake. The next dozen teeth were filed at 5-8 degrees of rake, and all the rest at zero degrees of rake. The idea is to use the toe for easy starting and to have aggressive rake for the remainder of the blade. Time: about 20 minutes. The saw arrived with quite a lot of set. Some disappeared in the filing, but a noticeable amount remained. Test cuts now make this saw about 20% faster than the spectacular yellow and black Stanley utility saw. It cuts rip very smoothly and cross cut slightly less smoothly, but acceptably fast. It’s faster in hardwood than in softwood, indicating I need just a little more set. … tomorrow’s improvement.

All done, I’ve sharpened some skills, saved an old saw from a trip to the land fill, gained what I consider a premium saw, and did it for about 1/10th the cost of a new premium saw.

Just wait til you see the next one…