• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Bob Easton

Chocolate powered woodworking

  • Home
  • Grinling Gibbons Tour

Pencil Box

April 24, 2010 by Bob Easton 11 Comments

Inspiration from Roy Underhill, Kari Hultman, and Dan Lauder. THANKS to all! (click any image for a larger version.)

photo of closed box photo of box with sliding lid removed photo of fully open box

Roy Underhill, author, Colonial era woodworking master, and proprietor of The Woodwright’s Shop, opened his 2009 season with the making of a palm sized grease pot that used a sliding lid and dovetail latch to secure its contents. Some of us live in parts of the country “too sophisticated” to carry a back woods woodworking show on TV. (New York City’s last country music radio station shut down in April of 1983, giving way to light jazz or some other kind of funk.)

So, along comes Kari Hultman, The Village Carpenter, to tell us about her replica of Roy’s little grease pot. Like Kari, I had that project on my to-do list. She got there first with a very nicely made box and some great construction photos.

It was Dan Lauder, and an approaching birthday, that moved the project to the top of the list with his discovery of an 1879 pencil box. While a bit different than the grease pot, the pencil box shared a similar 3 part construction of interlocking parts that qualifies it, like the grease pot, as “clever.”

The lid slides in a dovetailed track. Sliding it out reveals the top tray. That action also unlocks the top tray so that it can swing sideways revealing the bottom of the box. As an aside, the box that Dan discovered had a little pocket in top layer. I don’t know it’s purpose, but in my version, that pocket is now a resting place for a good luck charm, the happy little pig.

photo collage of making the pencil groovesOK, let’s look into how it was made. The lumber was stuff on hand, some tulip poplar. More about that later.

That roughly drawn sketch was my only “plan.” Like Kari, I used only hand tools. Unlike Dan, I don’t have a huge choice of planes, so I routed the pencil grooves with a scratch stock. It was slow going, but worked out OK. It needed more than one scratch. Use your sharp eyes to find my first error. It’s in the very first photo.

photo collage of making the lidThe sliding lid is about 1/8 inch thick. A router plane provided the space for it, and another small scratch (no photo) made the dovetailed tracks.

photo collage of making the bottomThe bottom, and the piggy’s nest, were excavated with forstner bits. Back to the router plane for cleanup. The last photo in this sequence shows that error corrected.

photo of raw edges and tack clothFinishing took more time than building. That’s because I don’t have a clean room for finishing (blame the tools) and I used a very slow drying paint. I wanted to use the same color as the gift recipient’s (not-yet-done) boat, a slow drying enamel. I call it “siren paint,” because as it dries it is constantly singing “Come to Me” to every dust bit in the building. To counteract the dust, I used a hand rubbed finish technique. After a few coats, that technique highlighted the fact that sharp edges need to be rounded to hold paint. So, correction and more coats. As an aside, the Norton tack cloth is a very handy aid. No more waxy cheesecloth.

Briefly, my hand rubbed finishing regime included: wet sanding with 600 grit, fine sanding with 0000 steel wool, rubbing with pumice, then with rottenstone, and lastly several layers of paste wax to bring to a high satin sheen. For service veterans, “spit shining” is the paste wax method that works best.

Lessons Learned

  • Double, triple, quadruple check that angled cuts lean the right way.
  • Hardwood would have been a better choice and avoided a few little “dings.” A lot of labor gets invested, and why invest in anything less than the best quality wood?
  • Double, triple, quadruple check that angled cuts lean the right way.
  • Make the sliding top thicker to lessen bow and give more “meat” to the dovetails.
  • Double, triple, quadruple check that angled cuts lean the right way.
  • A shellac sealer would have been better than the white sealer I used. The white really shows brightly when edge finish wears.
  • Double, triple, quadruple check that angled cuts lean the right way.
  • Slow drying paint gathers more dust than fast drying paint. (Doh!)
  • Double, triple, quadruple check that angled cuts lean the right way.
  • Finish gets really thin on sharp edges. Rounded edges hold finish much better and will wear better. I’ve often read this, but needed to wrestle with the problem myself, and ended up reshaping the work after several rounds of white undercoating showing up as I polished the finish.
  • Double, triple, quadruple check that angled cuts lean the right way.
  • Hand rubbed finishing takes a lot of time. Well actually, waiting for paint to dry firm enough for hand rubbing take a lot of time.
  • Starting 4 days before a birthday isn’t enough time when finishing alone needs 16 days.

Filed Under: Woodworking

Eva Too – Deck Trimming

April 23, 2010 by Bob Easton Leave a Comment

Phew! That little dimple in the deck (at the peak of the forward bulkhead) flattened out. Not that the 4 Jorgensen clamps had anything to do with it.

photo of shavings on the floor in the shape of a boatphoto of AccuScribe compassTrimming the overhang, inside and out, was the next task. There’s not a whole lot to this, other than burnin’ calories, almost a Milky Way’s bar worth. The outer edge of the deck was easy with the old 1897 Stanley #60 1/2 block plane. Inside curves, the cockpit area, are a different matter. I did them in two stages, first saw off most of the excess, then trim with a spokeshave.

Two tools are very useful for this task. The AccuScribe compass gave me another way of doing “reach around” marking. It’s 3 adjustment points give it a lot of flexibility, and also lots of possibility for something being loose. (Don’t ask.) The little Kataba saw is very handy. Like most Japanese saws, it cuts on the pull stroke, has a narrow kerf and hardened teeth.

photo of japanese kataba saw and a spoke shave

Filed Under: Boatbuilding, Eva Too, Mill Creek 13

Eva Too – Decked! Send More Clamps

April 22, 2010 by Bob Easton 2 Comments

Long ago, more than a week ago, I cut two large triangles of plywood for the deck and leaned them against the shop wall. If you are ever going to to this, make sure they lean in the direction that imparts a curve sympathetic to the curve of the deck, not the opposite. Don’t ask why I suggest this.

photo of template resting on the sheersOne of the first things to do after turning the boat over is to make a template with two curves, one an 18 inch radius, the other a 30 inch radius. It’s always good to have some 1/8 inch Luan plywood, other wise called “door skins,” on hand for patterns and templates. The template is used as a quide for shaping the  top edge of the sheer clamps. The small radius is for the fore deck, the larger for the aft. Space between is a rolling bevel that joins the two. The intent is to provide a flat landing surface for the deck, one that helps the deck fit neatly and maximizes the faying surfaces for glue contact. A super sharp block plane (1897 version) makes quick work of this step.

photo of drilling a painter holeAh, but before we close up the hull, let’s make a couple of holes in it. Yeah, I know. I’m adverse to holes in hulls, but these are different. They are ones that will never admit water. I like to use painters on my boats. They make it very easy to tie the boats to either the truck rack or something near the water. One of the reasons for making the false stems and burying them well was to provide solid timber for the painter holes. Forstner bits are fabulous! Start drilling from one side. Get the axis established. Then use a 1/16 inch pilot drill to poke through and establish the center that enables drilling from the opposite face. Voila, perfect, clean holes. Doing this now, before closing up that part of the boat makes it easy to ensure the holes won’t admit water.

Another name for stitch-n-glue construction is “tortured plywood.” The deck goes on in two parts. The aft deck is easier because the top of the bulkhead is a large radius and the plywood needs little torturing. So, under the prescription of “eat dessert first,” I did the easier deck first. The underside of the deck gets a clear coat of epoxy rolled on. Then, before it cures much, thickened epoxy is applied to the sheer clamps, the top of the bulkhead, the tops of the knees, and the carlins, every surface the deck will touch. Then the deck is flipped “jelly side down” onto the boat and fastened with ring nails every three inches. Ring nails are copper nails with rings cast onto their surface. Once pounded into place, they are very resistant to being removed.

photo of marking gauge in useOf course, all of this happens after carefully pre-fitting the deck and accurately marking every nail hole to within 1/256 inch tolerance. The challenge is knowing where to mark when the deck lumber is oversize (to be trimmed later) and the target for the nail is only 1/2 inch wide and invisible when marking. The helpful tool is the reach around marking gauge which is used to transfer the edge line. Mark the edge line, then mark a point 5/16 of an inch further inboard. One is then lucky to finally place the deck to within 1/4 inch of the fitting position. (Actually, 3 pilot holes and some brads helped with that.)

photo of forward deck's contortionsThe forward deck is more tortured.  The bulkhead has a much smaller radius producing a barrel like rounding. This rounding is counteracted by sheer lines that want to be smooth and flatter. Sitting in the boat, one sees the sides of the deck rise up to the barrel shape at the bulkhead and then swoop back down to near flatness before taking a short upward curl at the bow. photo of installed deckPre-fitting this deck entailed strapping it down in three places to mark the edges and nail holes. Installing it entailed abandoning many of those careful markings as the nailing proceeded. You see, three tight lashings is not a sufficient substitute for actual nailing every three inches, and the wood flares in interesting ways when tortured.

The forward deck meets the aft deck in the middle of the cockpit area. Making this join is a matter of sawing through the overlapped pieces with a very thin kerf Japanese pull saw. Simple!

No nails into the carlins. They are too scant. Simple epoxy bonding does the job, along with a lot of clamps, a couple of which are providing further torture to flatten a dimple. We’ll see what the morrow holds.

Two decks, four glue mixings, lots of banging and “talking to the boat,” made for a torturous day, more I think for the builder than the boat.

photo of ring nailsAn update for Larry and others who have not yet enjoyed using ring nails. They are intentionally tenacious. Once in, they hold. They can be extracted from soft wood, but bring the surrounding wood with them. When used in hardwood, extracting them usually means pulling the head off and leaving the nail in the wood. The heads are thin and two blows with a wide nail set will leave the heads nicely flush with the surface of soft wood, perfect for attaching decks. The ones shown here are #14 by 7/8 inch. Yet another form of torture (when they miss their mark).

Filed Under: Boatbuilding, Eva Too, Mill Creek 13

  • « Go to Previous Page
  • Page 1
  • Interim pages omitted …
  • Page 73
  • Page 74
  • Page 75
  • Page 76
  • Page 77
  • Interim pages omitted …
  • Page 129
  • Go to Next Page »

Primary Sidebar

Footer

Recent Posts

  • Sign Your Work!
  • New Frame Saw / Scroll Saw
  • Lamppost Sign
  • Goodbye PayPal – Goodbye Bob’s eBooks
  • Anarchist’s Workbench is Done

Categories

  • About
  • Artwork
  • Boatbuilding
  • Boating
  • bowl carving
  • Boxmaking
  • Clocks
  • Drawings
  • eBook
  • etude
  • Eva Too
  • Eva Won
  • Fiddlehead
  • Fiddlehead model
  • Flying
  • frame saw
  • gilding
  • green woodworking
  • Grinling Gibbons
  • Guns
  • Hand tools
  • Humor
  • kerfing plane
  • Lettercarving
  • Mill Creek 13
  • Model building
  • Power tools
  • Rant
  • resawing
  • scroll saw
  • Shopmade
  • sign painting
  • Stonework
  • Swimming
  • Technology
  • The Wall
  • treadle lathe
  • Uncategorized
  • VSD
  • Woodcarving
  • Woodturning
  • Woodworking
  • workbench

Other stuff

  • About
  • Contact
  • Privacy Policy

Copyright ©2024 · Bob Easton · All Rights Reserved