• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Bob Easton

Chocolate powered woodworking

  • Home
  • Grinling Gibbons Tour

Coaming

July 1, 2009 by Bob Easton 2 Comments

Coamings are intended to reduce the amount of water that splashes into a boat. Done right, they also add a bit of aesthetic detail. Fitting the coamings is a fussy job. They’re such a point of visual interest that they need to be done carefully.

coaming showing gapsThe first step was planing the carlins with a bevel that causes the coaming to flare outward just a bit.

The next step was preparing the stock. These boards are just a bit thin of 3/16 inch, having been resawn from a very clear piece of white ash.

A double ended boat offers an additional fitting challenge. In many cases, the point where each coaming piece meets can be a simple miter joint. However fitting two precise miters, each meeting perfectly at each end of the cockpit, could be an exercise in frustration.

fit an inboard filler blockThe answer is simple, uses a few more steps, but is far less tedious than getting two compound miters, and the precise length between them, right.

Start off by getting the boards to fit nicely in the cockpit. They get screwed, but not glued, in place.  There’s no glue here to enable future repairs. The boards are be a bit short of full length, as shown in the first picture (click to enlarge). That’s OK.

Then shape a filler block that fills the last inch of the join. The bevels were fun! Wood moves. Resawing and thicknessing was done over several days. Each day found the boards in a different state of cupping and warping. After screwing in place, the were mostly flat, but held just enough cupping to make beveling the filler blocks “interesting.”

trim the endNext, whack off the end of the combined boards and filler block.

Carefully!

Don’t scar the decks.

Yep, tedious.

Really sharp chisels and careful paring help at the bottom of the cut.

coaming tipsThe last bit is a piece to cover the blunt cut. Some mahogany does the job and adds a tiny bit of accent.

Fair the edges, screw and glue the bits to each other (and not to the deck – repairability), stand back and admire.

Then do it all over again at the other end.

Filed Under: Boatbuilding, Eva Won, Fiddlehead

Covering Boards and Decks

May 26, 2009 by Bob Easton 3 Comments

It’s looking more and more like a boat.

covering boardsThe covering boards, or long decks, cover the spaces between the sheer clamps and the long carlins. They are made from book matched resawn cedar slices finished to 3/16 inch thickness. Their undersides are sealed with a coat of epoxy. They are attached with epoxy and brass escutcheon pins.

After attaching the covering boards, four knees are added as additional framing for the short decks. They are spruce. Epoxied and screwed to the bulkheads and long carlins.

decksThe upper short decks complete the closing of the watertight compartments. They too are made from book matched resawn cedar slices finished to 3/16 inch thickness. Their undersides are sealed with epoxy. They are attached with simple household caulk and screws. No epoxy here because they might need to be removed occasionally.

Being a slow and deliberate builder is paying off. All of the recent work has moved along well with no time spent in the moaning chair. Most pleasing was avoiding inadvertent damage to the very thin very pointy ends of the upper deck boards.

Next come:

  • Coamings
  • False stems
  • Backrest (The seat is the bottom of the boat, no raised seat in this canoe.)
  • Footrest
  • Finishing (outside painted, inside and decks “bright”)

All of that will wait a few weeks while we do something else.

Filed Under: Boatbuilding, Eva Won, Fiddlehead

A New Marking Knife

May 14, 2009 by Bob Easton 1 Comment

knifeA beautiful new Pattern Pilot marking knife from Bob Zajicek at Czeck Edge Hand Tool is now hard at work in my shop. (Click image for a larger view.)

Making my own tools is something I enjoy, especially of I can make ones that function well and also look great. I’ve had drawings for marking knives waiting in the “to do” queue for quite some time and have been content to simply use pencils for the time being.

That changed last week when Al Navas ran a contest on his “Sandal Woods” blog. Al often has drawings for tools provided by his sponsors. I was very fortunate to win the marking knife as one of his Safety Week drawings. THANKS Al!

The knife is superb. It’s edge is keen and it feels great in the hand. Not only does it work very well, it is drop-dead beautiful. Maybe because I’m partial to blonds, I find the olive wood simply gorgeous. There aren’t any dovetails in the small boats I’m building, nor are there many straight lines. Yet, there are lots of ways to use this knife.

Not only is Bob Zajicek a very fine tool smith, he’s also a fortune teller. Along with the knife he sends not one, not two, but three plastic point guards. They are easily misplaced among the clutter of a busy project and the spares are appreciated.

Now, I can make marks that are 6 times more accurate than I can saw. A delightful tool. Very highly recommended! THANKS Bob!

Filed Under: Hand tools

  • « Go to Previous Page
  • Page 1
  • Interim pages omitted …
  • Page 91
  • Page 92
  • Page 93
  • Page 94
  • Page 95
  • Interim pages omitted …
  • Page 129
  • Go to Next Page »

Primary Sidebar

Footer

Recent Posts

  • Sign Your Work!
  • New Frame Saw / Scroll Saw
  • Lamppost Sign
  • Goodbye PayPal – Goodbye Bob’s eBooks
  • Anarchist’s Workbench is Done

Categories

  • About
  • Artwork
  • Boatbuilding
  • Boating
  • bowl carving
  • Boxmaking
  • Clocks
  • Drawings
  • eBook
  • etude
  • Eva Too
  • Eva Won
  • Fiddlehead
  • Fiddlehead model
  • Flying
  • frame saw
  • gilding
  • green woodworking
  • Grinling Gibbons
  • Guns
  • Hand tools
  • Humor
  • kerfing plane
  • Lettercarving
  • Mill Creek 13
  • Model building
  • Power tools
  • Rant
  • resawing
  • scroll saw
  • Shopmade
  • sign painting
  • Stonework
  • Swimming
  • Technology
  • The Wall
  • treadle lathe
  • Uncategorized
  • VSD
  • Woodcarving
  • Woodturning
  • Woodworking
  • workbench

Other stuff

  • About
  • Contact
  • Privacy Policy

Copyright ©2024 · Bob Easton · All Rights Reserved